Add to my favorite sellers. 3D Printer Kits 32 Bit Control Board MKS SBASE V1.3+MKS TFT32 LCD Touch Display Features: 1. Using 32-bit 100M Cortex-M3 LPC 1768 master chip, performance greatly improved. Support a high degree of modular open source firmware to facilitate the secondary development, eliminating the need to grasp the core code to worry about. Using 8825 as a motor driver to support 32 subdivision, performance far more than 4988, using SOP package, better heat dissipation.The stepper motor current is set directly without worrying about damaging the drive or potentiometer when adjusting the current. The circuit board uses high-quality 4-layer board, and specially made heat optimization. Using a dedicated power chip to support 12V-24V power input. Can be connected to 12864LCD. Before powering on, do confirm whether the positive or negative is connected correctly. Please do not plug the motor when it is powered on. It is easy to cause burned drive.
Do not run the motor in the process of adjusting the current. The correct way is that first disconnect the power, unplug the motor, and then re-power, adjust the potentiometer, measure the voltage on the potentiometer until the measured voltage is the same as expected. At present, MKS SBASE only support TFT series and LCD12864 display, not 2004, OLED display.
MKS SBASE and MKS TFT Touch Screen How to use: 1. Bin and config from config file to SD card (SD smaller than 64Gb). Need to change config name. Txt according to the configuration.
Refer to MKS-SBASE PIN , make correction connection. Such as stepper motor , endstops. Plug the SD card to the board, after power on, it will automatic update. If connect computer with USB, need to install the driver (Refer to below specification). Install the Driver: First, you should upload the zip file.
Then, plug the USB to computer. Then will turn up COM after install successfully.
Txt to SD card, insert to the board and power on, it will automatic update. After successful updated, the file name will turn into firmware. It is very easy to set the parameter. Txt on SD card, then modify the parameters and save. MKS TFT32 3.2 LCD Display: 1.MKS-TFT32 is a colorful touch screen LCD, it is suitable for many main board, such as MKS BASE, MKS GEN, MKS MINI, MKS SBASE, etc. Do not like MKS TFT28, MKS TFT32 do not support external power supply, can not work with Ramps1.4. Boot Setting: Step1: turn on MKS TFT32 at first time, then enter > setting > connection, select baud rate that the firmware use. Step2: enter > setting >model, choose printer type, only Delta and other two options Others: enter > setting > touch screen correction, improving accuracy. Firmware Update: Copy the latest update firmware to SD card root directory, including: 1. Please do not adjust the file name. Insert SD card, it will update automatically after restarts. MKS TFT can support MKS WIFI module.
After MKS TFT works with MKS WIFI module, can use Printrun, Repetier-Host to proceed remote connect and control. But it may make some functions unavailable. Configuration on single and double nozzle : change the value after the colon of cfg_sprayer_counter into the nozzle you need. (1 is single nozzle; 2 is double nozzle) 2. Heated bed configuration: change value after the colon of cfg_custom_bed_flag into custom requirements you need.(1 is with heated bed; 0 is without heat bed). 1 x MKS TFT32 3.2 inch LCD Display. 1 x MKS SBASE Board V1.3. Please contact me before you return it.
If item is defective after 3 months, you can still send it back to us. We will send you a new one after receiving the defective item.If you do not receive our reply, please kindly re-sent your message and we will reply to you as soon as possible. If you have any problems or concerns whatever with your order or products, please message us and give us a chance to assist you before you leave any feedback. We believe we can produce a positive outcome to any situation and will work hard to earn your praise. Our office hours are 9:00 a. M to 6:00 p. M (GMT +8) of Monday to Saturday. And our Office is closed on Sunday and public holidays. We apologize for the late reply during the holidays. The item "3D Printer 32Bit Control Board MKS SBASE V1.3+MKS TFT32 LCD Touch Screen Display" is in sale since Friday, November 17, 2017. This item is in the category "Computers/Tablets & Networking\3D Printers & Supplies\Parts & Accessories". The seller is "3dayandnight" and is located in ShenZhen. This item can be shipped worldwide.